Daikin BRP072A42 Mobile Controller Installation Manual
Main Component
Attach the Wireless LAN connecting adapter 2 Remove the adapter case (upper). to indoor unit.
In the case of B
Some models already have the connection cord D installed in the indoor unit. In such a case, please proceed from
Attach connection cord D to indoor unit.
- Remove the front grill of the indoor unit, then connect the connector of connection cord D to the white “S21” connector on the electrical wiring box.
- For instructions on how to remove the front grill or run the connection cord into D place, see the installation manual of the particular air conditioner. (Connection cord D can connect to connection cord HA)
Remove the upper front panel from the indoor unit and open the door, grab the connecting cord with your fingers and pull it out, then remove the binding band and pull the insulation tube off the connecting cord.
- Refer to your air conditioner’s installation manual for details on removing the upper front panel.
Remove the adapter case (upper).
Press a slot-head screwdriver* into the dent between the upper and lower cases to remove. (Be careful not to damage the case.)
- * Use a slot-head screwdriver with a wide head (5mm or wider is recommended).
Attach connecting cord to the product.
Attach the connecting cord connector (white).
- Fasten the connecting cord to the notch in the adapter case (lower)
In the case of A
Install the adapter case (lower).
- Install the adapter case (upper) so as to allow it to be easily removed for maintenance.
- Do not install outdoors or anywhere it is likely to get wet.
- Do not install it near the sensor part of the indoor unit.
Return the adapter case to its original state.
Close the adapter by hooking the top of the upper case on the top clip of the lower case.
Inserting Wireless LAN connecting adapter to indoor unit.
In the case of B
Grab the adapter case with your fingers, insert it back into the indoor unit and close the door.
Turn on the power supply
Wait until the initialization is completed (the lower panel is in the closed position). Open the door, remove the WLAN adapter and check that the [POWER] lamp for the product lights. After checking, return the WLAN adapter into the unit and close the door.
Configuration Configuratio
The customer is responsible for preparing the following
- Smartphone or tablet PC (Refer to our website for the latest information on supported operating systems.)
- Internet line and communicating device (Modem/router or a similar device)
- Wireless LAN access point (The corresponding channel for the Wireless LAN connecting adapter is 1-11.)
- [DAIKIN Mobile Controller] (Free of charge)
The setup is simple if there is a [WPS] button on the router (Wireless LAN access point).
- Check that the [RUN] lamp is blinking.
- If [AP] is blinking or lit, hold down the [MODE] button on the WLAN adapter for approximately 2 seconds until the [RUN] lamp blinks.
- Hold down the [WPS] button on the router (Wireless LAN access point).
- Operation of the [WPS] differs according to the router (Wireless LAN access point). Please refer to the documentation that comes with your router for more information.
- Hold down the [SETUP] button on the product for approximately 2 seconds.
- The [RUN] lamp on the product blinks more quickly. When the WLAN adapter and the router (Wireless LAN access point) are connected, this lamp lights. If you fail to connect, please try again from step 1 of “Simple Settings”. (It may not be possible to make the “Simple Settings”, depending on compatib
- Connect the smartphone (or tablet PC) and the router (Wireless LAN access point).
- Connection is possible by for example selecting the SSID of your router (Wireless LAN access point) from “Wi-Fi” in the smartphone’s settings and entering the router’s password.
- Tap the [D-Mobile] that was installed.
- Follow the directions on the screen to make the settings and for operation.
Troubleshooting Trouble
The following table provides brief descriptions of how to handle problems or uncertainties when you install the product or make connection settings. Check our website for details.
| When this happens | Explanation and where to check |
| None of the lamps light. |
|
| If you cannot find the system (air conditioner) on the system list screen, the product is not installed correctly |
Product lamp is extinguished.
|
Readmore and Download Daikin BRP072A42 Mobile Controller Installation Manual
| Title | : Daikin BRP072A42 Mobile Controller Installation Manual |
| Format | |
| Pages | : 4 Pages |
| Language | : English |
| File Size | : 3 MB |
| Model | : BRP072A42 |
