Honeywell FocusPro TH6320R Operating Manual
Honeywell FocusPro TH6320R Tabel Of Content
About your new thermostat
- Programming at a glance............2
- Quick reference to controls ........3
- Quick reference to display..........4
Programming & Operation
- Set time and day ........................5
- Fan settings (auto/on) ................6
- System settings (heat/cool)..........7
- Program schedules ....................8
- Program schedule overrides ....10
- Auto-changeover (heat/cool) ....12
- Remote control ..........................13
- Display outdoor climate............14
- Find lost remote control............14
- Special features ........................15
Appendices
- Battery replacement ..................16
- In case of difficulty ....................18
- Limited warranty........................19
- Regulatory information..............60
About your new thermostat
Your new thermostat is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed:
- Set time and day (required for proper operation) ...............See page 5
- Select fan setting (Auto/On)....................................................See page 6
- Select system setting (Heat/Cool) .........................................See page 7
- Program schedules: Preset to energy-saving levels
while you’re at work or asleep (assumes you wake at 6 am, leave at 8 am, return at 6 pm and go to bed at 10 pm).........................................................See pages 8-9
Quick reference to display screen
Set the time and day
- Press SET CLOCK/DAY/SCHEDULE, then press or to set clock.
- Press SET DAY, then press UP or DOWN to select the day of week.
- Press DONE to save.
Select the fan setting
Press FAN to select Auto or On. In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously.
Select the system setting
Press SYSTEM to select:
- Heat: Thermostat controls only the heating system.
- Cool: Thermostat controls only the cooling system.
- Off: All systems are off.
- Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
- Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat. Compressor is locked out.
Energy-Saving settings for maximum cost savings
This thermostat is pre-set to use Energy-Saving program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.)
To adjust program schedules
- Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE.
- Press UP or DOWN to set your weekday Wake time (Mon-Fri), then press NEXT.
- Press UP or DOWN to set the temperature for this time period, then press NEXT.
- Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
- Press NEXT to set weekend time periods (Sat-Sun), then press DONE to save & exit.
Program schedule override (temporary)
Press UP or DOWN to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the next programmed time period begins (see page 8). To cancel the temporary setting at any time, press CANCEL.
Program schedule override (permanent)
Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods.
The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed.
Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press CANCEL to resume the programmed schedule.
Auto Changeover (heat/cool)
Auto Changeover is a feature used in climates where both air conditioning and heating are often used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation.
Remote control
The optional remote control can act as a mobile thermostat, to maintain a comfortable temperature as you move
from room to room. When the system is responding to temperatures measured at the Remote, the thermostat will display Remote has Control.
Press CANCEL to restore temperature control to the thermostat (the system will only respond to temperatures measured at the thermostat).
Additional features
To display outdoor climate
If you have an outdoor air sensor, press MORE to display the current outdoor temperature and humidity. Press DONE to exit.
To find a lost remote control
If you misplace a remote control, press MORE, then FIND REMOTE. The remote will beep for two minutes to help you locate it. Press anywhere on the display screen to stop the beeping.
Special features
Built-in compressor protection: This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is re-started too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump).
Adaptive Intelligent Recovery: This feature eliminates guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set.
Battery replacement (thermostat)
Install fresh batteries when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted. Remove the battery holder and install 2 fresh AA alkaline batteries. After batteries are installed, the thermostat will automatically restore communication with the wireless network within a few minutes.
Battery replacement (outdoor air sensor)
Replace outdoor sensor batteries when the REPLACE BATTERY OUTDOOR warning begins flashing on the thermostat. The warning flashes about two months before the batteries are depleted.
Remove the sensor from the bracket, remove the cover and install 2 fresh AA lithium batteries. After batteries are installed, the sensor will automatically restore communication with the wireless network within a few minutes.
In case of difficulty
Heating or cooling system does not respond
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Wait 5 minutes for the system to respond.
Screen displays “No Signal”
Thermostat has lost radio contact with the wireless network (usually because of a power outage). To restore power:
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
After power is restored, the thermostat will automatically restore wireless communication within a few minutes.
Readmore and Download Honeywell FocusPro TH6320R Operating Manual
| Title | : Honeywell FocusPro TH6320R Operating Manual |
| Format | |
| Pages | : 21 Pages |
| Language | : English |
| File Size | : 480 KB |
