ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Manual

Task

Command/Explanation

Go to a Data Field

Press [∗] + [Field Number], followed by the required entry.

Entering Data

When the desired field number appears, simply make the required entry. When the last entry for a field is entered, the keypad beeps three times and automatically displays the next data field in sequence. If the number of digits that you need to enter in a data field is less than the maximum digits available (for example, the phone number fields *41, *42), enter the desired data, then press [∗ ] to end the entry. The next data field number is displayed.

Review a Data Field

Press [#] + [Field Number]. 

Data will be displayed for that field number. No changes will be accepted in this mode.

Deleting an Entry

Press [∗] + [Field Number] + [∗]. (Applies only to fields ∗40 thru *46, *94, and pager fields)

Initialize Download ID

Press ∗96. Initializes download ID and subscriber account number.

Reset Factory Defaults

Press ∗97. Sets all data fields to original factory default values.

Zone Programming

Press ∗56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RF transmitters.

Function Key Programming

Press ∗57. Unlabeled keypad keys (known as ABCD keys) for special functions

Zone Programming (Expert Mode)

Press ∗58. Same options as *56 mode, but with fewer prompts. Intended for those familiar with this type of programming, otherwise *56 mode is recommended.

Output Device Mapping

Press ∗79. Assign module addresses and map individual relays/powerline carrier devices

Output Programming

Press ∗80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers

Zone List Programming

Press ∗81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.

Alpha Programming

Press ∗82. Zone alpha descriptors

Exit Program Mode with installer code lockout

Press ∗98. Exits programming mode and prevents  re-entry by:  Installer Code + 8 + 0 + 0.   To reenter programming mode, the system must be powered down, then powered up. Then use method A above. See field *88 for other *98 Program mode lockout options.

Exit Program Mode

Press ∗99. Exits programming mode and allows  re-entry by: Installer Code + 8 + 0 + 0 or method A above.

This Device

Uses Address

Reports as ††

Enabled By…

RF Receiver

00

100

*56 zone programming: input device type entry

AUI 1

01

101

Automatic if AUI enable field *189 enabled for AUI 1

AUI 2

02

102

Automatic if AUI enable field *189 enabled for AUI 2

Long Range Radio

03

103

automatic if output to long range radio field *29 enabled

4286 Voice Module

04

104

automatic if phone module access code field *28 enabled

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 zones 33 - 40

module 5 zones 41 - 48

07

08

09**

10**

11**

107

108

109

110

111

*56 zone programming: input device type entry, then: automatic if

zone no. 9-16 entered as AW type or relay assigned automatic if

zone no. 17-24 entered as AW type or relay assigned automatic if

zone no. 25-32 entered as AW type or relay assigned automatic if

zone no. 33-40 entered as AW type or relay assigned automatic

if zone no. 41-48 entered as AW type or relay assigned

Relay Modules (4204):

module 1 module

2 module 3 module 4

12

13

14**

15**

112

113

114

115

*79 output device programming: device address prompt:

entered at device address prompt entered at device

address prompt entered at device address prompt

entered at device address prompt

Keypads: keypad

1 keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

16

17

18

19

20

21

22

23

n/a n/a

n/a n/a

n/a n/a

n/a 

n/a

data field programming as listed below: always

enabled, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

5800TM Module

28

n/a

automatic