About Epson EPL-N4000 Optional Parts
This Epson EPL-N4000 Optional Parts describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of EPL-N4000 Optional Parts. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.
Epson EPL-N4000 Optional Parts Contents
This manual consists of six chapters and Appendix.
CHAPTER 1. MAIL BOX(10-bin MULTIBIN)
CHAPTER 2. DUPLEX MODULE
CHAPTER 3. HIGH CAPACITY FEEDER(HCF)
CHAPTER 4. ENVELOPE FEEDER
Installation and Removal of Mailbox
HCF (High Capacity Feeder) must be installed in order to install the Mailbox.
Epson EPL-N4000 Installation
- Lock 2 casters at the front side of the HCF.
- Fix the Left Bracket and Right Bracket to HCF.
- Install Racks to Left Bracket and Right Bracket.
- Put the mail box on the printer. Make sure that protrusion of upper Rack is inserted into the hole of the stopper of the mail box.
- Install the Paper Stopper to the mail box.
- Pull out the Handle and hang it on the Stopper.
- Connect the cable of the mail box to the printer.
Removal (HCF is installed)
- Remove the cable of mail box from the printer.
- Remove the Handle from the Stopper and return it to the original place.
- Remove the Paper Stopper from the mail box.
- Pull out the stopper, pressing the Handle.
- Lift up the mail box and remove it fro the printer and Rack, and leave it on the floor or table.
- Remove Left Bracket and Right Bracket from Rack.
- Remove Left Bracket and Right Bracket from Rack from HCF.
Epson EPL-N4000 Disassembly and Assembly
Mailbox(10-bin Multibin) (See “PL15.1. Mailbox/ Sorter and Rack” on page -36“)
Epson EPL-N4000 Removal
- Disconnect P612 from the jack that is located at the rear of the printer. (See “Removal (HCF is installed)” on page -8)
- Unhook and remove the Stopper.
- Lift the Mailbox off of the Rack, and place the Mailbox on a level and stable surface. (See “Removal (HCF is installed)” on page -8)
- Press in on the latches securing the Rack to the Left and Right Brackets and lift the Rack up and off of the Brackets.
- Remove the thumbscrew securing the Right Bracket to the printer, lift the Bracket up to release the tabs, and remove the Bracket.
- Remove the thumbscrew securing the Left Bracket to the printer, lift the Bracket up to release the tabs, and remove the Bracket.
- Remove the four screws securing the Stand L Connection to the Left Bracket and remove the Stand L Connection.
- Remove the two screws securing Stand R to the Stand L Connection and remove Stand R.
- Remove the two screws securing Stand L to the Right Bracket, and remove Stand L.
Epson EPL-N4000 Assembly
- Attach Stand R to the Stand L Connection, and use two screws to secure Stand R.
- Attach the Stand L Connection to the Left Bracket, and use four screws to secure the Stand L Connection.
- Attach the Left Bracket to the left side of printer by first inserting the two metal tabs on the back of the Bracket into the two holes in the left side of the printer.
- Slide the Left Bracket down to lock the tabs in place.
- Use a thumbscrew to secure the Left Bracket to the printer.
- Attach Stand L to the Right Bracket, and use two screws to secure Stand L.
- Attach the Right Bracket to the right side of the printer by first inserting the two metal tabs on the back of the Bracket into the two holes in the right side of the printer.
- Slide the Right Bracket down to lock the tabs in place.
- Use a thumbscrew to secure the Right Bracket to the printer.
- Slide the legs of the Rack into the tops of the Left and Right Brackets.
- Push down on the Rack until it locks into place.
- Reinstall the Mailbox by carefully lowering the opening in the Mailbox support arm, onto the pin at the top of the Rack.
- Position the Stopper so when it is installed it blocks paper from exiting the right side of the Mailbox bins.
Read More Epson EPL-N4000 Optional Parts PDF Below
