Trane TCON401AN21MA Comfort Control Owners Manual

Trane TCON401AN21MA Comfort Control Owners Manual

Trane TCON401AN21MA Comfort Control Owners Manual Introduction

Congratulations on the purchase of your new Trane XR401 Comfort Control! Your XR401 Comfort Control combines the latest digital control technology with intuitive functions that make this control simple to understand and easy to operate. You’ll enjoy lower utility bills at the touch of a button with the energy efficiency features built into your XR401 Comfort Control. Your comfort settings are automatically stored in the XR401 Comfort Control’s memory eliminating the need for battery backup in the event of power loss. Simply follow the steps in this instruction manual and begin enjoying the benefits of your new Trane XR401 Comfort Control.

Trane TCON401AN21MA Comfort Control Features

Calibrate Outdoor Temperature

This option allows calibration (or deliberate miscalibration) of the outdoor temperature sensor. The selected number is number of degrees, plus or minus, which will be added to actual temperature. The number can range between + 5 and - 5 degrees in 1/2 degree increments. Factory default is 0. This adjusted value will be used and displayed as actual temperature. For example, if 2 is selected, 72 degrees actual will read 74 degrees.

Comfort Information Drawer

The drawer attached to the mounting base of the control is designed to provide a convenient location for the user to locate their local servicer. A standard business card can be folded and inserted into the slot on the drawer to remind the User whom to call when service is required.

Trane TCON401AN21MA Comfort Control Troubleshooting

Table 1 Troubleshooting

(Continued)

Symptom

Possible Cause

Action

Heating will not come on.

  1. System Mode not set to Heat.
  2. Minimum off time delay being enforced. "waiting displayed".
  3. Loose connection to control or system.4. Heating system requires service orcontrol requires replacement.
  1. Set Mode to heat and raise the setpoint above room temperature.
  2. If heating does not come on within 5 minutes, Check Heating.
  3. Check - Repair connections.
  4. Repair system / Replace control.

Cooling will not come on.

  1. System Mode not set to Cool.
  2. Minimum off time delay being enforced "waiting displayed".
  3. Loose connection to control or system.4. Cooling system requires service orcontrol requires replacement.
  1. Set Mode to cool and lower the setpoint below room temperature.
  2. If cooling does not come on within 15 minutes, contact servicer.
  3. Repair connections.
  4. Repair system / Replace control.

Cool ON  or Heat ON is displayed, but no

warm or cool air is coming from the registers.

  1. The heating equipment turns on thefan when the furnace has warmed up to asetpoint.
  2. Heating or cooling equipment is notoperating.
  1. Wait one minute after seeing the ON icon and then check the registers.
  2. Check Heating and Cooling system.

Control does not respond to keypad presses.

  1. "Keypad locked" icon is displayed on LCD.
  2. Keypad failure.
  1. Unlock keypad - press Up+Down arrow together until "Keypad Locked"disappears.
  2. Replace Control.

Fan does not operate properly in heat or cool mode.

  1. Incorrect wiring.
  2. Heating or cooling equipment inoperative.
  1. Correct wiring.
  2. Repair system.

Fan runs all the time.

  1. Fan mode set to ON.
  2. Shorted control wiring.
  1. Set fan mode to AUTO.
  2. Check / Repair wiring.

Display will not come on.

  1. Blown fuse or tripped circuit breaker.
  2. Furnace power switch OFF.
  3. Furnace blower compartment door or panelloose or not properly installed.
  1. Replace fuse or reset breaker.
  2. Turn switch to ON.
  3. Replace door panel in proper position to engage safety interlock ordoorswitch.

Temperature display is incorrect.

Temperature display needs calibration.

Calibrate Sensor - User Setup Step 49.

Outdoor temperature display is incorrect.

Temperature display needs calibration.

Outdoor sensor located in poor sensing location.

  1. Calibrate Sensor - User Setup Step 50.
  2. Disconnect sensor and check circuit resistance value - Table 4.
  3. Relocate outdoor sensor.

Cannot  set Heating setpoint above 80 degrees

Deadband between Heating and Cooling set to high

Decrease Deadband setting - User Setup Step 42.

"Service"  Flashing on and off.

Control EEPROM write error.

Press any key and Check / Re-enter Setup Choices.

"Service" solid on and "--" in temperature display.

Indoor temperature sensor open or shorted

Replace Control

Outdoor temperature display shows "--" and Service indicator on solid.

Outdoor temperature sensor open or shorted

  1. Check outdoor sensor wiring.
  2. Replace outdoor sensor.

Temperature setting will not change. (Example: Cannot set heating higher or cooling lower).

  1. Upper and/or lower temperature limits werereached.
  2. "Keypad locked" is displayed on LCD.
  1. Check the temperature setpoints:Heating limits are 40 - 85F.

    Cooling limits are 65 - 90F.

  1. Unlock keypad - press Up+Down arrow together until icon disappears.

Trane TCON401AN21MA Comfort Control Factory Default Settings

  • User Defined Options and Factory Default Settings: (See Table 1, page 19)
  • Temperature Display - Fahrenheit or Celsius (Default is Fahrenheit)
  • Auto or Manual Changeover - (Default is Auto)
  • Setpoint Deadband - 2 - 10 degrees (Default is 3 degrees)
  • Waiting Indicator - Enable or Disable (Default is Enable)
  • Cooling Droop - Off, 1, or 2 degrees (Default is 1 degree)
  • Energy Saving Cooling Setpoint Offset - 0 - 25 degrees (Default is 5 degrees)
  • Energy Saving Heating Setpoint Offset - 0 - 45 degrees (Default is 5 degrees)
  • Indoor Filter Timer Method - Calendar Days or Fan Run Time Days - (Default is Calendar Days)
  • Indoor Filter Timer Days - 1 - 180 days (Default is 30 days)
  • Calibrate Indoor Temperature - + / - 5 Degrees (Default is 0 degrees)
  • Calibrate Outdoor Temperature - + / - 5 Degrees (Default is 0 degrees)

Readmore and Download Trane TCON401AN21MA Comfort Control Owners Manual

Title : Trane TCON401AN21MA Comfort Control Owners Manual
Format : PDF
Pages : 12 Pages
Language : English
File Size : 1 MB
Trane TCON401AN21MA Comfort Control Owners Manual